Hello friends today i will show you how you can make christmas light show in very easy and cheap manner.
STEP 1:
COLLECTING THINGS
1. ARDUINO MEGA
2. 8 CHANNEL RELAY
3. JUMPER WIRES
4. BREADBOARED
5. USB B TYPE CABLE
6. PC
7. VIXEN 3 SOFTWARE
8. ARDUINO IDE SOFTWARE
STEP 2:
MAKING CONNECTION:
Take your relay and connect jumper wire to it. IN 1, IN 2, 3,4,5,6,7,8 will connect to arduino 2,3,4,5,6,7,8,9,10,11,12,13,a0,a1,a2,a3,a4,a5,a6 and so on pins. Remove jumper of relay and connect external power supply to it positive wire will go to jd-vcc pin and gnd will go gnd pin. Make sure that ground should be same for arduino and relay else it will not run. Here is how relay look like:
Step 3:
UPLOADING CODE TO ARDUINO:
Here is how arduino look like:
Upload code to arduino mega using usb b type cable. and connect it to your computer. Open your arduino ide software and copy and paste this code in your software:
There are a few #define lines on top to set the serial speed, the number of channels to use, and whether the relays activate with a high or low signal:
-Set the number of channels that you will use with the line #define CHANNEL_COUNT 16
-Set the mode line to "#define MODE INVERTED" or "#define MODE NOT_INVERTED" as needed. If your channels are doing the opposite than expected, change it to the other mode.
-Set the com port speed (currently to 57600) #define VIXEN_COM_SPEED 57600
-Set the timeout (in milliseconds) for Random mode with #define TIME_OUT 1000
It only uses 1 library for the watchdog timer, included in the arduino IDE, so just copy the code to a new sketch, change the channels, speed, and relay mode settings, and upload to your Arduino.
NOTE: If you use an Arduino Uno, remove all the #define lines for channels after 18, and remove those channels from the line with "int channels[] = {CH01..." as all those pins are only valid in the Arduino Mega and would give a compilation error in an Arduino Uno.
It works in the following way:
-Vixen needs to be setup to use a header of: ~!
-Sets all the channels to off in startup.
-Wait for up to 2 seconds (can be changed for longer) and if there is no valid input, it goes into random mode, blinking some lights on and off every second.
-If it detects valid input (with ~! header), it writes to the relays, as long as Vixen is working.
-If Vixen goes off for more than 2 seconds, back to random mode.
Here is the code:
// This code was written by Click that moment.
// To adapt the code to your case, just change this top section, with the #define lines.
// Includes the watchdog timer library
#include <avr/wdt.h>
// This sets how many channels will vixen be sending. Can be set to any number from 1 to 48 for Arduino Mega, and 1 to 18 for Arduino Uno.
#define CHANNEL_COUNT 16
// speed for the com port for talking with vixen. From 9600 to 115200. Use the same speed as set in Vixen.
#define VIXEN_COM_SPEED 57600
// Timeout waiting for serial input before going to random mode (in milliseconds).
#define TIME_OUT 1000
// If the relays turn On and Off opposite to Vixen sequence, change "#define MODE NOT_INVERTED" for "#define MODE INVERTED"
#define NOT_INVERTED 0
#define INVERTED 1
#define MODE NOT_INVERTED
// which pins control which channels
// You can change these assignment to use different pins, but be very careful to not repeat the same pin number for 2 channels.
// DO NOT use pings 0 and 1, as those are for the serial port to talk to the computer.
#define CH01 2
#define CH02 3
#define CH03 4
#define CH04 5
#define CH05 6
#define CH06 7
#define CH07 8
#define CH08 9
#define CH09 10
#define CH10 11
#define CH11 12
#define CH12 13
#define CH13 A0
#define CH14 A1
#define CH15 A2
#define CH16 A3
#define CH17 A4
#define CH18 A5
// Up to here for Arduino uno.
#define CH19 A6
#define CH20 A7
#define CH21 A8
#define CH22 A9
#define CH23 A10
#define CH24 A11
#define CH25 A12
#define CH26 A13
#define CH27 A14
#define CH28 A15
#define CH29 22
#define CH30 23
#define CH31 24
#define CH32 25
#define CH33 26
#define CH34 27
#define CH35 28
#define CH36 29
#define CH37 30
#define CH38 31
#define CH39 32
#define CH40 33
#define CH41 34
#define CH42 35
#define CH43 36
#define CH44 37
#define CH45 38
#define CH46 39
#define CH47 40
#define CH48 41
int channels[] = {CH01,CH02,CH03,CH04,CH05 ,CH06,CH07,CH08,CH09,
CH10,CH11,CH12,CH13,CH14,CH15,CH16,CH17,CH18,CH19, CH20,CH21,CH22,
CH23,CH24,CH25,CH26,CH27,CH28,CH29,CH30,CH31,CH32, CH33,CH34,CH35,
CH36,CH37,CH38,CH39,CH40,CH41,CH42,CH43,CH44,CH45, CH46,CH47,CH48};
int incomingByte[CHANNEL_COUNT];
int i = 0; // Loop counter
volatile unsigned long timer_a = 0; // new line
//setup the pins/ inputs & outputs
void setup(){
// enable the watchdog timer with a time of 1 second. If the board freezes, it will reset itself after 1 second.
wdt_enable(WDTO_1S);
// specifically for the UNO
sei();
// initalize PWM Channels / Pins
for (i=0; i < CHANNEL_COUNT; i++){
pinMode(channels[i], OUTPUT);
}
// set all the realys to off to start with
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
digitalWrite(channels[i], LOW);
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
digitalWrite(channels[i], HIGH);
}
}
testSequence();
// set up Serial according to the speed defined above.
Serial.begin(VIXEN_COM_SPEED);
}
void loop()
{
if (Serial.available() >= (CHANNEL_COUNT+2)) {
wdt_reset(); // resets the watchdog
timer_a = millis (); // new line
int uno = Serial.read();
if (uno == 126){
int dos = Serial.read();
if (dos == 33){
for (i=0; i < CHANNEL_COUNT; i++) {
// read each byte
incomingByte[i] = Serial.read();
}
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
int value = incomingByte[i];
if (value <= 127) {
digitalWrite(channels[i], LOW);
}
else {
digitalWrite(channels[i], HIGH);
}
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
int value = incomingByte[i];
if (value < 127) {
digitalWrite(channels[i], HIGH);
}
else {
digitalWrite(channels[i], LOW);
}
}
}
}
}
}
// Random mode code. Random mode starts if no serial input has been received in TIME_OUT millisenconds
else {
wdt_reset(); // resets the watchdog
unsigned long diff = millis() - timer_a;
if (diff >= TIME_OUT) {
timer_a = millis ();
int random_a = 0;
for (i=0; i < CHANNEL_COUNT; i++){
random_a = random(0, 2);
if (random_a == 0) {
digitalWrite(channels[i], LOW);
}
else {
digitalWrite(channels[i], HIGH);
}
}
}
}
}
void testSequence(){
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
wdt_reset(); // resets the watchdog
digitalWrite(channels[i], HIGH);
delay (500);
digitalWrite(channels[i], LOW);
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
wdt_reset(); // resets the watchdog
digitalWrite(channels[i], LOW);
delay (500);
digitalWrite(channels[i], HIGH);
}
}
}
If you are using arduino uno make sure to delect extra channel else your code will not compile.
STEP 4:
PROGRAMING SOFTWARE:
First of all download vixen 3 software in your computer.
Here is the link: http://www.vixenlights.com/category/vixen-3/
open your software
Click on setup display:
Add single item:
Name that item for example i named it Trees:
On the right side add generic serial:
Name your controller for example i named it controller 2:
Now add number of relay you want to connect i write 22:
Now configure generic serial setting:
Click on setup and change serial port:
Here com port will be automatically shown when you had connected arduino to your pc. define baud rate to 57600. click ok.
click on send header text. And type ~!.
NOW YOU ARE DONE WITH SETTING UP SOFTWARE AND ARDUINO HARDWARE THEY BOTH ARE NOW CONNECTED.
Now will need to set up a sequence. click on new sequence:
Now associate song by clicking song icon:
Now click on tools audio and beat bar detection:
Now right click on timeline select add effect and add alternating:
And put that effect where you want to relay to turn on. And create a sequence by putting that effect on time at different part of song for example:
NOW YOU ARE DONE WITH EVERYTHING NOW GO AND CREATE YOUR OWN CHRISTMAS LIGHT SHOW AND ENJOY. MERRY CHRISTMAS.
HERE HOW IT LOOKS LIKE: